|
Post by RAM Z on Nov 27, 2014 12:26:46 GMT -5
There is a brace under the floor, that runs side to side, that has the seat belt bolt holes in it. I need the hump area cut to weld into my coupes floor. Just the brace. If anyone has a parts car with a good floor in that area let me know and Ill tell you exactly where I need it cut out. Four door, 64-67 are all the same. Doesnt have to be an Olds, can be any A body.
Thanks
|
|
|
Post by boba65442 on Nov 27, 2014 14:49:45 GMT -5
I'll look to see if its decent
|
|
|
Post by oldolds88 on Nov 28, 2014 10:43:57 GMT -5
i may have that piece from a 66, same?
|
|
|
Post by Big Mike on Nov 28, 2014 12:54:23 GMT -5
I know the one on the vert I'm stripping is absolute toast. I will check the one in the post coupe when I get back from the holiday, that won't be until Tuesday.
|
|
|
Post by RAM Z on Nov 28, 2014 13:21:46 GMT -5
i may have that piece from a 66, same? Yes same piece. If you look under the car, the brace has a "scallop" on the flat area, on each side of the tunnel. Im guessing its to let water out. I need from scallop to scallop.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Nov 28, 2014 14:05:14 GMT -5
I`ll watch this thread, post if you get what your looking for, I have a few floor pans in the barn in Michigan, I`ll grab one next time I`m there if you don`t come up with what you need.SO LONG AS YOUR NOT IN A HURRY
|
|
|
Post by oldolds88 on Nov 28, 2014 14:30:48 GMT -5
is this the part?
|
|
|
Post by oldolds88 on Nov 28, 2014 14:31:57 GMT -5
is this the part?
|
|
|
Post by oldolds88 on Nov 28, 2014 14:34:04 GMT -5
damn fingers,
|
|
|
Post by RAM Z on Nov 28, 2014 14:43:26 GMT -5
No, the one I need has two square nuts welded on the underside for the seat belts to bolt into.
|
|
|
Post by oldolds88 on Nov 28, 2014 14:47:34 GMT -5
this has the two outer seat belt nuts.
|
|
|
Post by oldolds88 on Nov 28, 2014 14:50:31 GMT -5
sorry those are body mount holes. i do have the othe piece,its on a body thats off the frame.
|
|
|
Post by oldolds88 on Nov 28, 2014 14:51:10 GMT -5
going to run out in the blizzard and look at it.
|
|
|
Post by RAM Z on Nov 28, 2014 14:55:06 GMT -5
Thanks!
|
|
|
Post by oldolds88 on Nov 28, 2014 15:06:56 GMT -5
|
|
|
Post by RAM Z on Nov 28, 2014 15:13:08 GMT -5
Yes, thats the one. But it needs to be solid because Im going to weld it into my car. The circled area is the scallop, I need it cut from one scallop to the other.
|
|
|
Post by oldolds88 on Nov 28, 2014 15:27:34 GMT -5
it is solid,just looks bad because of the angle i was shooting,
|
|
|
Post by oldolds88 on Nov 28, 2014 15:29:21 GMT -5
im in laingsburg mi.
|
|
|
Post by RAM Z on Nov 28, 2014 15:43:39 GMT -5
Im an hour an a half away. Can I cut it out? Ill have to take some floor with it if thats OK. Im guessing that a parts car.
|
|
|
Post by oldolds88 on Nov 28, 2014 15:51:44 GMT -5
yep,parts car. when ill begone tonight but will be home tomorrow. cell 517 6142324 robert
|
|