|
wanted
Mar 8, 2023 20:06:31 GMT -5
Post by oldolds88 on Mar 8, 2023 20:06:31 GMT -5
WANTED LH vent window post # 5717169LH would like mostly pit free even on the jamb seal side. reasonable price or trade for ?
|
|
|
Post by oldolds88 on Jan 14, 2023 22:17:18 GMT -5
careful,they break easy
|
|
|
Post by oldolds88 on Jan 14, 2023 22:16:32 GMT -5
to fit what? 64 or 65 floor shift /stick or column shift. i have some of each but not all the switches and stuff. but nice face plates rob text 5176142324 for pics
|
|
|
Post by oldolds88 on Apr 3, 2022 21:05:36 GMT -5
whats up with the 64 cutlass header thread? go to the bottom and its spam and gibberish
|
|
|
Post by oldolds88 on Mar 27, 2022 20:45:14 GMT -5
i have 3 of them,1 is an old old casting. am redoing the tail panel more to scale. the real old one has chrome grille and bumpers. i shaved off the 442 scoops as my replica is my sterling mist 65 i had in high school. the other is going to be a red one like my bro in law had before he went to nam. in my research,the 67 442 kit has tint 442 decals that fit all the places on the 65.
|
|
|
Post by oldolds88 on Mar 23, 2022 0:13:30 GMT -5
thanks joe
|
|
|
Post by oldolds88 on Mar 21, 2022 7:48:53 GMT -5
thanks, i seen that, has anyone used that kit? just want to be sure itll work,so i dont have more stuff laying around that doesnt fit.
|
|
|
Post by oldolds88 on Mar 20, 2022 11:12:10 GMT -5
anybody know what hinge pin kit fits the 65 2 dr.cutlass? going thru all the listings just makes my head hurt, i need pins,bushings and rollers. thanks for any and all help. rob
|
|
|
Post by oldolds88 on Mar 15, 2022 19:34:29 GMT -5
there is a foam gasket that fits in a groove in back of bucket. not available anywhere i know. i bought 1 1/2" wide urathane ribbon,like they use on windshields, only a lot wider. ill cut it to fit.
|
|
|
Post by oldolds88 on Dec 25, 2021 19:30:43 GMT -5
i have a cabin in grayling, have friends in harrison and lots of relatives in the clare area,maybe have a bite some day
|
|
|
Post by oldolds88 on Dec 15, 2021 20:06:36 GMT -5
i used two methods to remove the undercoating on mine,1 heat with torch on back side,scrapes easy, 2. i twisted a short sawzal blade and used the swzal.
|
|
|
Post by oldolds88 on Jun 25, 2021 12:12:18 GMT -5
did you receive the pics i sent? let me know if i can help rob
|
|
|
Post by oldolds88 on Jun 14, 2021 19:34:10 GMT -5
i got some,text 5176142324,ill show what i have. rob
|
|
|
Post by oldolds88 on Apr 18, 2021 20:41:32 GMT -5
drill a small hole in it and use spray contact cleaner in it.
|
|
|
Post by oldolds88 on Mar 25, 2021 19:40:36 GMT -5
as far as i know,after looking at both,the entire metal tail panel will fit. 65 lights wont fit in 64 panel,but if wanted the 64 lights and trim panel, go for it. metal panel will fit
|
|
|
Post by oldolds88 on Dec 22, 2020 14:42:48 GMT -5
if its in and everything bolts up without prying on parts,use it. other frame mounts may have been different vendor. bolt it in,check your pinion angle and fan shroud for clearance.
|
|
|
Post by oldolds88 on Dec 1, 2020 23:33:27 GMT -5
i have z bar, clean and powder coated black. bought it for mine,then decided to go hydraulic. might also have the stud for motor end. linkage from pedal to z bar,has wear,also z bar to fork. text for pics,100 + ship 5176142324. rob
|
|
|
Post by oldolds88 on Oct 31, 2020 21:10:48 GMT -5
mark the position of the old hinges before you remove the old ones,or use the old paint lines,that will put you in the ballpark. dont tighten the hinges totally till youre done,snug to hold the door,yo adjust you may need to smack hinge with a hammer and flat bar,where they bolt to the body loc,move upper hinge foreward,pulls the rear of door up lowwer hinge brings it down. bolts on hinge to door move door in or out,upper does top lower is bottom. you should be close enough that you only need minor taps to adjust. make sure your striker bolt is in good shape,they get worn down with bad hinges. line door then line stryker,again up,down,in, and out,slightly loosen and tap till door closes. check all gaps,they sjould be even all around . you can use a piece of wood the size of the gaps you have now,to check. its a lot easier done than said.
|
|
|
Carpet
Jul 8, 2020 20:55:33 GMT -5
Post by oldolds88 on Jul 8, 2020 20:55:33 GMT -5
if he doesn't take it I may be interested. price?
|
|
|
Post by oldolds88 on Jun 29, 2020 23:31:04 GMT -5
ii used vht aluminum header paint,closest so far
|
|